Skip to main content

Software templates for industrial shredder control

Pre-programmed machine templates: Motion-Axis Shredder

With its three software packages — Basic, Advanced, and Pro — Baumüller offers differently tailored templates for the drive system specifically for the recycling industry. This saves the customer a lot of time, especially during the initial phase of the project, and allows them to focus fully on process programming. All templates already include a large portion of the required machine functions, including motion blocks for controlling the servomotors. In addition, features such as commissioning mode and load balancing, as well as various protection and analysis functions, are available.

NEW

NEW
The new generation of b maXX servo converters features a drive-integrated PLC for decentralized automation concepts and highly synchronized motion control. The drive-integrated control unit b maXX drivePLC can perform complex motion control, technology, and control functions directly in the drive. This eliminates the need for any additional external hardware; an external controller and the communication module are no longer required. The b maXX servo converters with PLC inside support all common fieldbuses such as EtherCAT, Ethernet POWERLINK, CANopen, Modbus, ProfiNet, Varan, and EtherNET/IP. OPC UA can also be used, if needed, as an interface for transferring data between various devices, such as visualization systems or edge controllers, among others.

The right package — tailored to your needs

BASIC

  • Protect your machine
  • Control of the shredder shafts

ADVANCED

  • Protect your machine
  • Control of the shredder shafts
  • Analyze your machine

shredder software cube PRO

  • Protect your machine
  • Control of the shredder shafts
  • Analyze your machine
  • Operate and control your machine (Engineering as a Service)

The Basic Package can be easily imported into the b maXX drivePLC drive-integrated controller via Plug & Play. It includes all necessary motion functions, such as controlling the shredder shafts via the b maXX servo converters. The machine's mechanical parameters can be parameterized very easily, rather than having to go through the time-consuming process of programming them. To simplify communication with the machine controller, it also includes a predefined OEM interface for exchanging the system's setpoint and actual values, such as setpoint and actual speed. The Deviation Monitor blockage detection system with corresponding slip clutch protection is included as standard. The speed is measured at the converter's high switching frequency. Exceeding the configurable limit values thus leads to immediate detection of the fault condition. This protects the drive system and saves money.

The Advanced package builds on the Basic template and includes additional analysis features. The Smart Energy Monitoring and Smart Condition Monitoring analysis tools are integrated directly into the Baumüller b maXX servo converters and use the data available in the drive for analysis—without any external sensors. With Smart Energy Monitoring, optimization opportunities can be identified and leveraged based on energy consumption. Smart Condition Monitoring uses recorded and analyzed process parameters as reference values to keep a close eye on the mechanical condition of your machines. By performing regular comparative measurements during operation, potential mechanical problems are detected early on, helping to prevent costly downtime and keep your machines running smoothly.

The Pro Package allows you to take full control of the machine. The most powerful package is based on the Advanced package and additionally offers machine operation and control, including intuitive machine visualization and recipes for material processing. In this context, individual requests and requirements can be optimally incorporated during implementation as part of our Engineering as a Service (EaaS Link). 

Different shredder concepts — one machine template

All packages in the Motion-Axis Shredder software template are suitable for single-shaft and dual-shaft shredders with or without a feed mechanism, and can be integrated into various hardware concepts.

Industrial shredder concepts in comparison

Time advantage: parameterizing instead of programming

The already programmed subsystem contains frequently needed machine functions for crushing and can be easily loaded into the shredder control system. The movements then merely have to be parameterized. The machine programmer no longer has to worry about the basics during development. For the machine builder, this means a faster time to market, and significantly reduced development expenditure.

From small to large — one template for all shredder expansion stages

Motion-Axis Software-TemplatePre-programmed and ready for immediate integration: With the Motion-Axis Shredder software template, both shredder drive systems with a single shredding unit …

Motion-Axis Software-Template… as well as high-performance shredders equipped, for example, with two shredding units—each featuring two double-winding motors—and a feed motor can be controlled

Template with all basic movement control functions

In addition to the shortened development time, with the Motion-Axis Shredder software template, machine manufacturers also benefit from the recycling industry technology experience. For example, the operation of two motors with load balancing in one shaft is already preprogrammed. The customer only has to integrate the existing communication interface, and can then, among other things, control the shredder shafts directly via a speed setpoint.

Templates for Baumüller controls and drives

Basic Package

Control of the shredder shafts

  • Plug & Play
  • Intelligent control of shredder shafts
  • Commissioning mode
  • OEM interface for 3rd-party controls
  • Scalable machine performance
  • Various expansion stages are easy to parameterize
  • OPC-UA server

Safety feature (Deviation Monitor)

  • Blockage monitoring for shredder shafts via speed monitoring
  • Detection of clutch slip in fast controller cycles increases drive train reliability
  • Machine protection and cost savings

Advanced Package with additional analysis features

Smart Energy Monitoring

  • Monitoring of the drive's energy consumption using simulation algorithms
  • Creating transparency and cost savings

Smart Condition Monitoring

  • Monitoring of the drive system to detect mechanical changes
  • Wear reduction and cost savings

Pro Package with additional machine control (Engineering as a service)

Machine operation and control

Intuitive machine visualization

Recipes for material processing

Are you interested in buying our products?

Write us a message, our sales experts will be happy to advise you.

System solution for shredders

With its software template, Baumüller has for many years been consistently moving towards being a full-range supplier. In addition to the software package, the system solution for shredders includes the complete main drive system with high-torque motors and servo converters including control cabinet construction as well as the control technology with hardware.

Find out more about our drive solutions for industrial shredders here.

The circular economy meets energy efficiency: 30 percent lower energy costs thanks to direct drive technology

Working with Baumüller, WEIMA Maschinenbau GmbH developed a high throughput single shaft crusher with high-torque drive

Reduce operating costs - increase output

The manufacturer of shredding and compacting machines WEIMA expands its drive portfolio with an all-electric high-torque system solution.

  • System solution comprising motor, servo drive, gearbox and slipping clutch
  • Flexibility in connecting the drive to the rotor shaft
  • Baumüller x WEIMA: Driving innovation forward together
 

Downloads

Brochure / Flyer

Shredders

PowRex – the all-electric high-torque drive solution from Baumüller
Engineering | Hardware | Software